February 8, 2021

How to Run Security Camera Wires Outside USA 2021

Topic : How to Run Security Camera Wires Outside USA 2021

How to Run Security Camera Wires Outside

How to Run Security Camera Wires Outside USA 2021

Are you stuck on how to run CCTV wires or cables outside or in your home? Here you’ll get a detailed step-by-step guide to show you how to install the outdoor and indoor safety camera wires.
Even if you are the first time to run the CCTV cables, you can install the security camera wires through the attics / walls, for the front / back door, the reception room, the front / back yard, the shop floor, the bedroom, the garage, the warehouse, the basement, the parking lot. Parking lot, farmhouse, entrance, even top floor, etc. quickly and easily. In this article we have considered How to Run Security Camera Wires Outside.

Big tip: if you choose battery powered security cameras, you can just place the cameras outside or inside without worrying about wires and cables.

The main things you will need to connect your security cameras
When you are about to wire your safety cameras outside or indoors, you should prepare the necessary items below.

For PoE security cameras:

  • Cat 5/6 Safety Camera Wire
  • Exercises
  • Fish bar
  • PoE syringes
  • For wireless security cameras (without battery):

Electrical wires

  • Exercises
  • Fish bar
  • Security Camera Extension Wire

For analog surveillance cameras:

  • RG-59 BNC connectors
  • Crimping tool RG-59
  • RG-59 stripping tool
  • RG-59 / syv-75-5 coaxial wires
  • BNC barrel
  • Wire cutter
  • Standard Wire Crimping Tool
  • Electrical tape

You can look at the security camera wire diagram below before running the cables.

Note: How to Run Security Camera Wires Outside, Some of the detailed tools are not mentioned here. You can see the best tools for drilling holes here. If you need to run underground wires for security cameras to monitor your garden, driveway, etc., PVC / Metal Channels are essential. Check this post for cloud ip camera.

Part 1. How to turn on security camera wires at home.
Installing security camera wiring inside your home, such as attic, roof, siding, etc., is much easier than an outdoor job.

You can follow this safety camera wire installation guide to hide or run wires in your home.

The first step: designing the central monitoring center before installing the CCTV cables. Where you put your NVR / DVR – the central monitoring center – in your home determines the wiring path. Putting an NVR / DVR intelligently in your home can help you eliminate the mess of messy wires.

The location should be easy to reach so you can conveniently attach your security camera from anywhere in your home. Your attic and internet router are ideal places for your NVR / DVR.

Note: You can get useful tips here for placement of surveillance cameras (s).

Step 2. Turn off the power when operating the wires of the surveillance cameras, which will protect your personal safety and avoid damaging your equipment.

The third step. Punch a hole where the exit will be (for wireless security camera and analog security cameras), and use a metal coat hanger to feel the wall for any unexpected obstructions.

Drilling is undoubtedly one of the best and easiest ways to pass security camera wires through walls, floors, vinyl siding, etc.

If you run the Cat 5/6 Ethernet cable for your security camera, you can just drill a hole to run the Ethernet cable from the camera to your home router or NVR. If the distance between the camera and router / NVR is too far, you can add a PoE injector.

Step 3. The gap / hole should be greater than the maximum amount of wires you expect to run. Allow a few feet of extra wiring inside for both termination and future reorganization if needed. Labeling the ends of the cables will help you know which safety camera works with which cable.

Step 4. Go to where you want to install your security cameras, such as an attic, ceiling, basement, or crawl space, then drill a hole in the top or bottom of the wall panel in the same cavity as the wall.

Step 5. Attach the wires to the fish tape to catch the wires of your security camera.

Step 6. Run the wires or cables of the security cameras to the destination (you may need a partner to supply the wires for you). Remember to use a safety camera wire protection cap or conduit to protect the cables.

, , , , , ,

Leave a Reply

Your email address will not be published. Required fields are marked *